Posts Tagged With: Recycled

Bicycle Gardening

Yes, what to do with the surplus of rusty and twisted bicycle wheels that no longer are able to serve the purpose for which they were made? If  you are like me, you just cannot bring yourself to send them out to pasture at the metal recycler’s – somehow that just doesn’t seem right.

IMG_1588

Well, I found some other uses for these wheels – in the garden. Check these out for starters:

IMG_1600

Towers for scarlet runner beans – add some EMT conduit to those rusty old rims, splash on some spray paint to cover the rust, and VOILA! in no time, scarlet runners will thank you for providing a place to climb, and you will thank them for adding their lovely scarlet red flowers to the beauty of your garden. The bees will thank you also!IMG_1601 2

As you can see, the towers are “geared” for the job. Sorry, I couldn’t resist that.

IMG_1602

Beet cages. No, not to keep the beets in. Rather, to keep the hungry jack rabbits out. There is a very healthy population of rabbits in the city, and last year when I went to harvest the beets from my plot at the community garden, I discovered that the rabbits had “beet” me too it. (Sorry, I couldn’t help that one either) So this is a test run to see  if this will work.

IMG_1603

Broccoli protection. My green thumb partner grows the very best broccoli, starting the seeds inside while snow is still on the ground and then moving the plants into our wicking raised beds. We usually eat broccoli right up until the snow flies in the fall again. This year we are going to be selfish and not share with the cabbage butterflies who like to infest the plants. I wrapped crop cover around the frames, allowing sunshine and rain in and keeping the butterflies out.IMG_1605

There is a shot from further back with both frames covered. Oh, yes, and an excuse to show off the cargo e-bike that I built last year. That is my favoured ride when going to the community garden to check for those pesky rabbits!

Advertisements
Categories: Rescued and returned to use | Tags: , , , , , , , | Leave a comment

E-cargo Part 2

Cargo bikes are great for transporting much more than conventional bicycles and with that advantage, of course, there is a downside – they are bigger and therefore heavier to pedal. For several years, I have been happy to do the extra work required in exchange for that benefit and have done most of my short distance grocery and other shopping trips with my cargo bike, but have not used the bike as much as I would have liked for longer trips.

In December,  2014, a new bike, the Biktrix Juggernaut, was introduced to Saskatoon, featuring an electric mid-drive. It was the mid-drive system used on that bicycle that caught my interest and the following summer, I contacted Biktrix owner, Roshan Thomas, and arranged to go for a test spin on a bike equipped with the Bafang system.

Wow – what a hoot that was, and it got me thinking about its application on a cargo bike. While short distance shopping trips are not difficult on a cargo bike, longer distances can be quite daunting due to the extra weight of a heavier bike plus its cargo. As one of my friends commented, electric assist changes a cargo bike into a regular bike when considering the effort involved. I decided to give the idea a try on the new bike that I was building.

bbs02_2048x2048.jpg

The Bafang mid-drive system has been on the market a relatively short period of time but has already received a lot of consumer attention and mainly good reviews. It is available in several models – after discussions with Roshan, I chose the mid range BBS02 36 volt 500 watt unit, and coupled it with a Panasonic 36 volt 14.5Ah lithium battery pack for my new cargo bike.

Installing the conversion is not difficult. Bearings, bearing shells and crank are all removed from the bottom bracket and the drive unit slides in. Controls include throttle, on/off/power level selector and brake levers that cut power when  brakes are applied. A large readout panel displays speed, distance travelled, power level selected and battery level. The unit is programmed to engage when the crank is pedalled forward or when the throttle is used. Other programming options are available.

Unlike rear hub electric motors, mid-drive systems retain the advantage of whatever range of gearing that  a bike may have. They can be coupled with rear derailleur systems or with internal geared hubs. Derailleur systems are inexpensive but require more attention in shifting when using electric assist, and can result in jerky and stressed gear changes. Internal hubs eliminate that concern and I chose another newcomer on the market, the Nuvinci N360 continually variable hub – it represents the latest in technology.

nuv-hubguts.jpg

This is what the new drive system and rear hub looked like on the new bike.

IMG_2494

The battery is mounted on a rear carrier, over top of the drive wheel. The Bafang unit is not obtrusive – rather it looks like it belongs where it is.

This is the view from the cockpit. The Bafang read-out is large and easy to read. The NuVinci twist-grip shifter displays speed settings as a gradient.

So, how does it work? It is a bit early for a full assessment but so far, I am very pleased with the results. The Bafang powers the bike very well and the NuVinci hub makes changing speeds a breeze. After  more than 30 kilometres, the battery is still at 80% charge. I have been out for several short distance shopping trips and have travelled in record time. The bike moves along easily at 25 km/hr, even with a load of groceries on board. I have not tried for a top speed but have been over 30 km/hr, which for a cargo bike. is moving right along!

More photos to follow in the next post, and a follow-up after the bike has logged a few miles and done some work to earn its keep. Cheers.

IMG_2507

Categories: Cargo bikes | Tags: , , , , , | Leave a comment

Grocery cargo…

Working CB

Winter has been with us for a while and my “new” cargo bike has been safely stowed away while waiting for  a return to spring. This one was built in early summer 2014 when unusually rainy weather made it unsuitable for sailing. As this year comes to a close it is time to post some photos before a newer “new” version replaces it, hopefully with some more improvements. Photos tell the story of this build better than words.

IMG_8357

The cro moly donor frame – with damaged forks and a badly rusted in seat post

 

 

 

 

IMG_0474

To make it easier to line up the various sections of the bike, I built some stands to hold them at the correct level.

 

 

 

 

IMG_0475

Solid central kickstands are essential on long john cargo bikes. When surfing the net one day I came across some photos of an approach that I liked. Unfortunately I have not been able to find that site again so that I could credit the builder!! I am certainly grateful to him for sharing – if he should ever happen upon this post, I want him to know my appreciation. These pictures show the bike upside down on the bench.

IMG_0507

IMG_0509 IMG_0508

 

 

 

 

 

 

 

After adding paint and some components, this was what came out of the workshop:

IMG_9845

IMG_9842

 

IMG_9840IMG_9846

IMG_9837

IMG_9838

 

The cargo area has been built to be used either as a flat bed, or with box sides sized to hold two grocery baskets.

 

 

There are some marvellous builders that are building cargo bikes. I would like to acknowledge one in particular, John Lucas, of Cycle Trucks based in West Sacramento, California. He makes some great cycles – check them out. I like his X-style step through frames – this is my attempt.

IMG_9833

 

This bike has been a lot of fun – folks often comment on it when I am out shopping. I added a lot of features to it, but of course, there are always ways of improving. With that in mind, could this be the donor frame for the next one?

Next donor?

Categories: Cargo bikes | Tags: , , , | Leave a comment

Moustachio – the transformation is complete

IMG_8644

Once the components were chosen, assembly could take place. Wheels were greased and trued. Duro Sierra tires were selected – puncture resistant, with reflective sidewalls. Derailleurs were installed – the front one original and the rear one new – a Shimano Alivio RD-M410. Cabling was configured for derailleurs and brakes.  Wrap-around fenders and a sturdy rear carrier were included in the mix, adding functionality and style. My Lion Bellworks bell was transferred from the Expediter light duty cargo bike to the new city bike.

Then for a new experience – wrapping the moustache handlebars. Before tackling the job, I went online and discovered that there are as many experts on the topic as there ways to wrap handlebars. By combining the ideas and approaches that seemed to make the most sense to me, the job was completed and the results very satisfying.

Next up – a test ride, followed by a photo shoot. The test ride proved exhilarating – the light frame and narrow tires coupled with the ability to “get down” on the moustache bars produces a fun ride that turns heads when you stop long enough for folks to appreciate it. Great fun.

IMG_8642

IMG_8639

IMG_8651

IMG_8650

IMG_8638

Categories: Rescued and returned to use | Tags: , , , , , , , , , , , | Leave a comment

Moustachio – the ingredients for a transformation

Well, in the last post, it was clear that some there was still a lot of work to get that old Norco bicycle looking presentable. It required removing ALL of the paint, including the original very nice two tone job, and in addition, all of the decals and stickers. I will spare you the details – suffice it to say that it took time, elbow power and several sheets of sandpaper. Once the bike was “clean to the bone”, it was time for the “paint booth/bike shed” and the metallic Pearl Glow paint that had been selected. Here we are, just hanging around, waiting for paint to dry…

  IMG_8607

Next? the fun part – after cleaning old components that were to be recycled, it was time to select and find the new ones that would make the transformation. You may recall that I mentioned something in the last post about moustache handlebars… Let me tell you the story of the origin of this style. It goes back to the 70’s in Japan when school children fell in love with the drop down handlebars of racing bikes. For some reason, school authorities felt that these bars were too, well, too riske!! and they banned the use of them by school children. But the kids found a way around that by modifying the original style. Perhaps it is the wanna-be-rebel side of me then that is drawn to this style of handlebar… :o)

So, lets have a look at those “rebels”. Here they are, resting nicely in a stem that I picked up a year ago, originally used on a lowrider bike that had been trashed. Yes, those bars may not look like much yet, but take time to wait for the outcome.

IMG_8610

I knew that the Shimano quick shift combination levers that were originally used on the Norco bike could not be used with these handlebars. Bar end shifters are in common use with moustache handlebars and it is easy to see why. However, I did not have these and I did not want to spend the money to buy them but there was an alternative that I was certain would work…

IMG_8614

Yes, something ‘old school’ – Shimano shifter levers from a road bike from the 70’s, attached to the stem. There were a collection of these shifter levers in a coffee tin in the “parts” department of my workshop  and by mixing and matching and searching through a pile of old road bikes that were destined for the recycle melting pot, I was able to put together a set that looked good and worked well.

Next – brake levers… My research had disclosed that non-aero brake levers were the best choice when using moustache bars and while going through that pile of old road bikes, I found a possible candidate set. I was not completely satisfied because the hoods on them were long gone. About the time that I found these, serendipity stepped in. An ad appeared on Kijiji for a “mint condition vintage drop bar shimano brake lever set”. The ad described them as coming from “a 1978 Miele road bike, the drop bar is a “Sakae Custom Road Champion”  in near perfect condition minus wear from original install…  The brake lever set is Shimano, both levers come with hoods which are in good shape”. I inquired to see if the levers could be purchased separately but was told that they would only go as a set. An hour later, the vendor messaged me back to tell me that someone wanted to buy the handlebars only, and so I quickly went to pick up the levers and hoods – here they are…

IMG_8608

As you know, it takes a bit more than handlebars, shift and brake levers to make a bicycle but in this instance, these were the most interesting components. With these now on hand and with the paint finally cured, check out the next post to see the final outcome of this transformation.

Categories: Rescued and returned to use | Tags: , , , , , , , , , | Leave a comment

Moustachio – potential for another transformation

A year ago, I rescued a bike that was destined to be collected, along with a lot of other discarded steel products, and then be melted down and recast into rebar, or some other useful but uninteresting product. Like many bikes that are being discarded, the cables were rusted and non-operative and tires were flat. Brake pads were worn out, and one wheel was badly bent. The bike wasn’t very attractive – someone had done a very poor spray paint job over much of the bike in green, followed by an equally poor brush job done in an unappealing grey. It was barely possible to make out that the bike was a NORCO product, a chrome-moly frame originally built as a mountain bike. It was clear that this bike had had a hard life and was going to need a lot of attention to make it into anything that anyone would want. It was set aside, until this year – I was introduced to moustache handlebars and this was the perfect bike on which to try them out.

IMG_8182

Here are some shots of the bike, after a partial disassembly and after most of the initial re-paint had been removed. By this point, the bike had been mostly disassembledIMG_8170

IMG_8179

IMG_8158

IMG_8164

IMG_8157

IMG_8163

IMG_8152

IMG_8161

IMG_8174

Yes, not a pretty picture, but if you know what to look for, you can see the potential. Stay tuned – next post will offer some options and hope for better times.

Categories: Rescued and returned to use | Tags: , , , , , , | Leave a comment

The Jack and Jill makeover – the RESULTS

IMG_8249

These are the parts that go into a bicycle and this is the pile that was left after “Jill” was taken apart. Now lets see the results after  a manicure and some new “duds”. First the paint:

IMG_8278 IMG_8276

Remember those rusty, rough looking bikes that we began with? Already looking different, right? Next its time for the nuts and bolts basics – cleaning and greasing and adjusting bearings, and running new cables to make sure that brakes work and gears change. All the important but boring stuff – it needs to get done to make the best out of any bicycle. After thats done, we can get to the fun part – let’s see what else we can do….

IMG_8559

Let’s start at the top, with new Velo anatomic comfort grips. Along with the grips, aluminum Tektro linear pull brake levers, designed for four finger ergonomics.

IMG_8560

New tires and tubes start us on the road with CST Commuter street tires – smooth rolling with a continuous central band lined by water runners and triangular shoulders to enhance traction. Braking is important on a bicycle and dual colour brake pads were installed. These pads are designed with channels to guide excess water and grime off of the braking surface. For those days when a rider might be caught by a sudden rain, full coverage fenders were added front and back, constructed of light weight but strong polycarbonate and installed using stainless steel hardware.

IMG_8564

KMC Rustbuster chains were installed to provide long lasting trouble free service. The LU-214 City Pedals from Wellgo were selected – they are made of one piece aluminum with a Kraton rubber gripping surface and Cro-Mo machined spindles. Light weight aluminum bottle cages as well as convenient kickstands were added.

IMG_8562

Classic alloy rear racks were also added to make it easier to carry “stuff”.  And to ensure a comfortable shock absorbing ride, a Rhyno Comfort Web Spring saddle was chosen, with thick foam top, coil springs at the rails and a web spring.

So how did we do when all comes together?

IMG_8555

IMG_8553

IMG_8566

There you have it – the Jack and Jill Makeover. Available for you at Village Cycleworks. Time to dig those bikes out of the garage, bring them on over, and get the NEW LOOK. Turn those dusty, rusty, trusty “mountain” bikes into modern, city loving, commuter friendly, exercise ready Prairie Cruisers!! Why buy something new when what you have is still very serviceable and only needs some new additions and improvements to bring it back to life? Give me a call and lets talk!!

IMG_8571

 

Categories: Rescued and returned to use | Tags: , , , , , , | 1 Comment

Working Cargo – for sale

 

 

Yes, that hard working lime green beauty is for sale. Summer is closing in – another cargo bike is taking shape on the jig in the shop and so room has to be made for the newcomer.

cargo load

That bike and I have had some good times this summer – picking up groceries for the evening meal and propane gas to cook it.

RecyclingWe have taken cans and bottles to the recycling depot.

To the recycle depot

Loaded

 

We have replenished our supply of cans also. By the way, for anyone needing supplies for a party, the cargo deck will hold 6 dozen cans in one layer, twelve dozen if you double it… :o)A beer run

 

One of the unexpected advantages of a cargo bike came one day when we stopped for a coffee at one of our favourite spots, The Roastery at Five Corners. There were no tables left in the shade so we pulled the bike under a tree, and parked ourselves on the cargo bay – instant park bench!!IMG_5302_2

 

 

 

 

Working cargo

 

 

 

For fun we have carried lumber home from the lumberyard, – just to see if we could do it!!

Recently we used the bike to get us to a picnic on the river, carrying the chilled wine and our contribution to the feast along with our folding chairs – good times!

Heading to a picnicYes, good times for the next owner also. Who will it be? See the ad on Kijiji, or send me a note if you want to be the one.

Categories: Cargo bikes | Tags: , , , , , | 2 Comments

Jack and Jill – a make-over of matching bicycles – the BEFORE pictures

 

IMG_8242

In a few days, the paint will have cured on “Jack & Jill”, a pair of bikes that are getting a “make-over” in the Village Cycleworks shop. I picked these bikes up a few weeks ago – they were destined to be crushed, melted down and “recycled” into new metal products. I decided to use them as a sort of a test case. How much consumer interest is there in a different type of recycling? – one that requires human energy and effort rather than mechanical effort and petroleum based energy.

Here are the “before” pictures  of these “Made in Canada” bikes. They looked a bit rough around the edges with paint chips and scratches and surface rust on handlebars and wheels. The tires still held air but were showing their age with checks and cracks. Brake and derailleur cables were rusty and seized and no longer able to function. Seats were in decent shape and still as uncomfortable to ride on as they were when they were new. With all of this going against them, I wanted to see how they would look after they had been given a little TLC and few additional components to bring them into the 21st century. Stay tuned to see how they turn out.

IMG_8243 IMG_8244 IMG_8245 IMG_8247 IMG_8248 IMG_8266

Categories: Rescued and returned to use | Tags: , , | 1 Comment

From neglected to SWANKY!! – the Schwinn Cruiser

The big blue frame had a forlorn, abandoned look about it. Rust on the fenders and mud on the white sidewalls didn’t hold out much promise but I could see behind that facade of disrepair and neglect that there was a swanky beach cruiser waiting for a second chance to woo the ladies. This is what the bike looked like when it arrived at Village Cycleworks.

IMG_7916
IMG_7905 IMG_7906IMG_7907IMG_7911IMG_7912IMG_7913IMG_7914IMG_7915 IMG_7918

It is often remarked that a bit of elbow grease can work wonders, and this cruiser provides ample evidence to support that. Careful work with a soft scratch pad along with the ubiquitous WD-40 was used to remove most of the rust. A stiff bristle brush cleaned up the tire sidewalls. The back wheel with its two broken spokes was replaced with a wheel  salvaged from another bike and equipped with a white sidewall tire.  The broken brake lever was replaced by one also salvaged from elsewhere. Missing brake pads were also replaced. New cables and cable housing ensured that components would function correctly. A simple but trusty thumb shifter was traded for the poorly functioning twist grip shifter. New grips were installed. A caged bearing in the bottom bracket was replaced. Duct tape over the torn seat cover completed the job. Here are the results. What do you think? 

IMG_7990IMG_7974 IMG_7976IMG_7977IMG_7978IMG_7982IMG_7983IMG_7988

Categories: Rescued and returned to use | Tags: , , | Leave a comment

Create a free website or blog at WordPress.com.